Tuesday, December 11, 2007

12V to 120V Inverter

Inverter dari 12 V ke 120 V AC

Have you ever wanted to run a TV, stereo or other appliance while on the road or camping?

Well, this inverter should solve that problem. It takes 12 VDC and steps it up to 120 VAC. The wattage depends on which tansistors you use for Q1 and Q2, as well as how "big" a transformer you use for T1.

The inverter can be constructed to supply anywhere from 1 to 1000 (1 KW) watts.

Part
Total Qty.
Description
C1, C2268 uf, 25 V Tantalum Capacitor
R1, R2210 Ohm, 5 Watt Resistor
R3, R42180 Ohm, 1 Watt Resistor
D1, D22HEP 154 Silicon Diode
Q1, Q222N3055 NPN Transistor (see "Notes")
T1124V, Center Tapped Transformer (see "Notes")
MISC1Wire, Case, Receptical (For Output)


Notes

  1. Q1 and Q2, as well as T1, determine how much wattage the inverter can supply. With Q1,Q2=2N3055 and T1= 15 A, the inverter can supply about 300 watts. Larger transformers and more powerful transistors can be substituted for T1, Q1 and Q2 for more power.
  2. The easiest and least expensive way to get a large T1 is to re-wind an old microwave transformer. These transformers are rated at about 1KW and are perfect. Go to a local TV repair shop and dig through the dumpster until you get the largest microwave you can find. The bigger the microwave the bigger transformer. Remove the transformer, being careful not to touch the large high voltage capacitor that might still be charged. If you want, you can test the transformer, but they are usually still good. Now, remove the old 2000 V secondary, being careful not to damage the primary. Leave the primary in tact. Now, wind on 12 turns of wire, twist a loop (center tap), and wind on 12 more turns. The guage of the wire will depend on how much current you plan to have the transformer supply. Enamel covered magnet wire works great for this. Now secure the windings with tape. Thats all there is to it. Remember to use high current transistors for Q1 and Q2. The 2N3055's in the parts list can only handle 15 amps each.
  3. Remember, when operating at high wattages, this circuit draws huge amounts of current. Don't let your battery go dead :-).
  4. Since this project produces 120 VAC, you must include a fuse and build the project in a case.
  5. You must use tantalum capacitors for C1 and C2. Regular electrolytics will overheat and explode. And yes, 68uF is the correct value. There are no substitutions.
  6. This circuit can be tricky to get going. Differences in transformers, transistors, parts substitutions or anything else not on this page may cause it to not function.
  7. If you want to make 220/240 VAC instead of 120 VAC, you need a transformer with a 220/240 primary (used as the secondary in this circuit as the transformer is backwards) instead of the 120V unit specified here. The rest of the circuit stays the same. But it takes twice the current at 12V to produce 240V as it does 120V.
  8. Check out this forum topic to answer many of the most commonly asked questions about this circuit: 12 - 120V Inverter Again. It covers the most common problems encountered and has some helpful suggestions.



Pernahkah Anda menginginkan menghidupkan TV, stereo, atau peralatan lainnya ketika di perjalanan atau wisata?

Kalau ya, berarti inverter yang ditampilkan di sini bisa menolong Anda. Inverter ini hanya perlu tegangan 12 V DC untuk kemudian diubah menjadi 120 V AC. Besar dayanya (watt) tergantung pada transistor yang Anda gunakan untuk Q1 dan Q2, juga pada berapa besar kapasitas trafo T1.

Inverter ini dibuat untuk melayani beban 1 sampai 1000 watt (1kW).

Catatan:

  1. Q1 dan Q2, juga T1 menentukan besar daya yang dapat disuplai oleh inverter ini. Dengan Q1, Q2 = 2N3055 dan T1= 15A, inverter ini mampu menyuplai sekitar 300 watt. Untuk meningkatkan daya perlu diganti dengan trafo yang lebih besar lagi ditambah transistor yang berdaya besar.
  2. Cara paling mudah dan murah untuk mendapatkan T1 yang besar adalah untuk menggulung ulang trafo microwave lama. Trafo ini berdaya sekitar 1 kW dan sempurna. Cari di tempat servis TV/elektronik, cari yang paling besar. Makin besar microwave-nya, makin besar juga trafonya. Ambil trafonya dengan hati-hati, jangan memegang bagian tegangan tingginya, mungkin masih ada muatannya. Tes dulu, tapi biasanya masih baik koq. Kemudian, pisahkan bagian sekunder 2000 V tanpa merusak bagian primer. Gulung 12 lilitan kawat tembaga (berisolasi), buat center tap dan gulung 12 lilitan lagi. Besar diameter kawa tembaga tergantung berapa besar arus yang direncanakan akan lewat di situ. Kokohkan lilitan dengan isolasi. Jadi deh. Jangan lupa untuk menggunakan transistor berkapasitas arus besar untuk Q1 dan Q2. 2N3055 yang ditampilkan di sini hanya mampu menangani arus 15 A masing-masing.
  3. Ingat, kalau mengoperasikan alat ini untuk menyuplai daya besar, arus yang ditarik dari baterai/aki juga besar, jangan samapi baterai/aki habis setrumnya.
  4. Karena rangkaiana ini menghasilkan 120 V AC, Anda harus menggunakan sekering dan masukkan ke dalam casing/kotak.
  5. Untuk C1 dan C1 HARUS dari jenis kapasitor tantalum. Kalau dari jenis elektrolitik yang biasa, akan panas dan bisa meledak. Nilainya harus 68 uF, jangan diganti.
  6. Jika menggunakan komponen lain selain yang disebutkan di sini, mungkin saja rangkaian ini tidak bekerja.
  7. Kalau Anda ingin membuat tegangan output 220/240 V AC, maka dibutuhkan trafo dengan gulungan primer 220/240 V. Gunakan terbalik, 220/240 V sebagai tegangan keluaran/output. Rangkaian yang lain boleh sama dengan yang menghasilkan 120 V, tapi ingat, arusnya di sisi 12 V menjadi 2 kali lipat.

2 comments:

Unknown said...

bisa merubah inverter swichting engga ? kalau bisa tolong hubungi kembali saya yach ?

heri juno said...

saya cuma pengen menghidupkan lampu motor bertegangan 100w/24v dengan AKI 12v,bisa gak yaa..?
Lobisa gimana caranya $ gimana Rangkaiannya..???
Mohon Bantuannya...
Hatur Nuhun...